Music is a beautiful way to unwind and reconnect with oneself. It’s tough to relax and appreciate music if it’s distorted or crackly while you’re attempting to play it.
Speakers are commonly used to increase the volume of pleasing sound. At times, though, one speaker may sound louder than the other. There are several possible explanations if you’re having such difficulty.
There will be different reasons behind one speaker sounding louder than the other. It’s because of poor quality of speakers, lousy wire connection or signal source etc. There are a few things you can try to fix your speakers, so your audio comes out clear and crisp.
If you find yourself in this scenario, read our thorough post. We’ve outlined numerous solutions to repair and get rid of this situation. The steps will be super easy to give a try.
What Are The Reasons Behind This Distortion?

There could be tons of reasons behind this, and we have spotted a few most common reasons. Check them out, and one of them may be the reason you are unable to enjoy music.
- Errors in Wires
Your speaker’s wires may be broken or damaged or have got loosened. Just check the wires, check if they are passing the signal current properly or not.
- Improper Signal Source
If the speaker doesn’t get good power, then it cannot produce a proper sound. Sometimes, if your amplifier cannot produce a proper signal for your speakers, you may face one speaker working fine. But another one isn’t working as it should be.
Improper Connection speakers have a particular power connection system; there is a probability that one of them is not working correctly. Check the power connection. The wire might have been damaged or the power socket
How to Fix “One Speaker Louder Than The Other”
Now let’s get down with our main event and learn about how you can fix the problems. Use the simple steps below.
Step 1: Swap The Speakers

The first step is to rearrange the speakers. This will reveal whether the issue is with the speaker or anything else. Make sure your speaker wire ends are in good condition, and no stray wire strands hang out before swapping speakers. Assemble them in their proper connections, making sure they’re neat and secure.
When you’re sure about the wiring, do what Metropolis advised and change the speaker cables to the speaker on the opposite channel. This should help you figure out whether the problem is with the amplifier or with the speaker.
Also, if your amplifier has a Mono switch, set it to Mono for a time as you listen. If the sound is similar in Mono, the signal source is likely the problem (DVD, CD, Phono, Tape, etc…). Unfortunately, the majority of modern amps lack a mono switch.
Before switching speakers, make sure the speaker wire ends are in excellent condition. Check for stray wire strands as well.
Step 2: Correct Your Wiring

Both speakers must have the (+) or Red terminal of the amplifier connected to the (+) or Red terminal of the speaker. The system will not sound correct if one speaker is hooked Amp (+/Red) to Speaker (-/Black).
Suppose your speaker wire isn’t already color-coded. In that case, one of the pair’s wires will most likely have a rib molded into the plastic insulation that runs the length of the wire to help you recognize one from the other. It makes no difference if the Ribbed wire is Red(+) or Black(-), as long as it is constant.
As a result, double-check your wiring to ensure that all connections are correctly connected. If the connection between the speaker and the amplifier appears to be loose, it should be repaired.
It is suggested that you inspect the cables of your speaker. Replace the damaged speaker cable with a new one if the wires are broken. As a result, double-check your wiring to ensure it’s in working order.
Step 3: Check the sensitivity settings

Slight variations in sensitivity settings are usual, but what you’re describing appears to be severe. So the first thing I’d do is double-check that the speakers and their accompanying cords are in good working order.
Because it’s in a node from one and an antinode from the other, it’s also feasible that the measuring microphone catches different levels from each speaker! You can hear the problem in your situation, and thus it’s clearly more than a measuring issue.
When listening in stereo, a failed bass driver or one-legged balanced cable (where one of the two signal wires has broken) would substantially diminish the total loudness. However, it may not be immediately apparent. Swapping the speakers around (having set their rear-panel settings the same) and then swapping their wires is the simplest way to perform these checks. If the louder side shifts, you’ve located the source of the problem!
Step 4: Check the balance

When you hear the 3rd tone on both speakers, you know your speakers are balanced. It should sound like it’s coming from a place in the middle of the speakers. If your speakers don’t sound balanced, change their location and check each speaker’s balance/volume level on the amplifier or computer/device separately.
Make sure both speakers are operational and at the right volume by checking your cabling or balancing controls. It’s also possible that you’re using a mono connection, and your amplifier is only showing one sound channel.
First, check the device’s equalization (if it has one) since it may be adjusted incorrectly. If your speakers are connected to a pair of wires or audio transmission cables, be sure the colors are correctly matched, or they will be “out of phase.” If the sound is still distorted, make sure the wire or speakers aren’t physically damaged.
The speaker and amplifier connection might be sloppy at times, resulting in poor sound quality. If the nuts that are connected by wires fail, this issue might emerge. Keep any loose connections you find between the speaker and the amplifier.
FAQs:
- Question: What causes one speaker to be louder than the other?
Answer: It’s either the cables or the source if the low volume shifts to the opposite side. It’s either the amp or the phone if the low volume doesn’t switch sides. It’s the amp if it happens on both the phones and the speakers.
- Question: Why is my audio louder in one ear?
Answer: Dirt and earwax can collect inside the mesh of headphones when they are worn often, which tends to obstruct volume flow. Only one side of the room is generally quieter due to dirty earbuds. Before throwing away the complete set, you may quickly locate filth on the earphone’s surface and clean it.
- Question: Why is my right speaker quiet?
Answer: Make sure the stereo system’s speaker balance is adjusted to the middle position. Make sure the speaker cable is correctly connected to the audio system’s rear. Replace the speaker cable if the problem persists. Remove the speaker connectors from the audio system if the problem persists.
- Question: What is a crossover speaker?
Answer: A crossover, in its most basic form, is the frequency at which sound transfers from one audio source to another, often a speaker. The sound transitions from the speaker channels to the subwoofer in a passive speaker are determined by electrical crossover components.
Closing Words
One of the techniques listed above should have resolved the issue of hearing uneven speakers. Just look for the reasons and try the fixes as described.
Two speakers are typically placed on improving the overall audio system. They are linked to the amplifier. However, one of them may not operate well at times. Frequently, one speaker appears to be louder than the other.
Always remember that only correctly functioning speakers can provide high-quality audio. As a result, if one of your speakers is louder than the other, you must take action.