With needle nose pliers, you may be able to remove any remaining chain that is even a small amount. Depending on whether the fan is linked directly to power (rather than being regulated by a wall switch), you may want to turn off the breaker to prevent the fan from running while you are working (to keep your wits).
If you didn’t have the switch, you would have to supply current to the appropriate wires to adjust the fan speed. Assuming that this is a mechanical device (as opposed to an electronic device), the only way to alter the setting is to move the switch to a different location.
You will find detailed information in this article on how to turn off a ceiling fan without using a chain. In addition to that, you will get answers to some of the frequently asked questions that will help you better understand this topic. The article also provides alternative methods to turn off the ceiling without a chain. Go through the article keenly to get all the required information.
How a ceiling fan is turned off

1. An extension for the pull chain is recommended
2. What to do if the ceiling fan pulling chain is broken inside the fan
3. Remove the ceiling fan’s base by unscrewing it from the ceiling.
4. The pull chain switch should be removed.
5. Remove the Pull Chain Switch wires on the ceiling fan and store them somewhere safe.
6. Connect the new pull switch to the ceiling fan’s dimmer control.
7. Back out of the pull chain via the hole with the pull chain threaded back through it.
When the ceiling fan lights stop working, the reason for their failure isn’t usually as fundamental as a blown light bulb or a faulty wiring harness. This can result in loose wire connections at any point along the wiring path, from the wall switch to the lighting kit. It is also possible for the fan’s lights to quit functioning because of damaged light sockets or a broken pull chain switch.
Switch on the ceiling fan and take a position precisely beneath the fan blades, keeping an eye on the propellers as they rotate. Low-speed rotation of the blades (from the top to your right, then down to your left, and finally back up to the top) will draw cool air up from beneath the surface of the water.
How to fix a pull chain switch

1. To ensure the safety of everyone, turn off the electricity at the circuit breaker.
2. Disconnect the light bulbs from the sockets to avoid breaking.
3. To remove the screws that hold the light fixture in place, use a screwdriver to pry them out.
4. Remove the switch by unscrewing the nut located on the fixture’s side.
5. Pulling out the switch allows you to examine the chain more carefully.
Changing the pull chain on your fixture the cable connections that lead from the pull chain control to the unit should be identified. Remove the switch by disconnecting the cables and pulling it out. Change the original switch with a new pull chain control, and then replace the end cap on the light fixture to complete the transformation.
Troubleshooting a ceiling fan

To diagnose the root cause of a ceiling fan that will not start, follow the methods outlined below: Verify that the electricity is turned on by checking the circuit breaker. Turn off the electricity by tripping the circuit breaker. Check to see that the fan blades are spinning freely. Confirm that the reverse switch is not neutral by pushing it in.
The capacitor is typically housed within the fan’s switch housing, which is black. Additionally, if the case looks to have been burned or melted in any manner, this indicates a faulty capacitor, and it should be changed. Please keep in mind that other elements in the circuit could also be affected by the faulty capacitor.
How a three-speed fan switch works
Hot voltage is connected to the primary winding at three distinct points in a three-speed motor. Power is only applied to one place at a time. That is precisely what the fan switch accomplishes. When power is applied to each location, the primary coil is energized because the voltage from the Black Hotwire completes the circuit with the White Neutral wire, and the secondary winding is de-energized.
The process and requirements when changing a ceiling fan

Shut down the power by turning off the fuse or circuit breaker box. There may be multiple pairs of cables in the roof box, so keep an eye out for these. There is a possibility that some of them are connected to circuits that are different from the one that the bulb you are working on is connected to. Keep yourself safe by following these guidelines: Before installing a ceiling fan, use a circuit tester or cut off the electricity to the entire house.
Removing the four screws located on either the bottom cap or the side of the fan switch housing will allow you to access the switch housing. Pull the pull chain out of the switch casing by unscrewing the ornamental nut located beneath it. Make a note of the location of each wire’s connection to the chain. Immediately after you’ve marked the wires on the pull chain, you should remove them from the pull chain.
If a blade is slanted downward and the fan is turned on the same side as the blade angle, the air will be forced forward. Like the last case, when one of the blades is slanted downwards and the fan turns the other way, the opposite is true. The air will move in the opposite direction.
It’s perfectly safe to leave the air conditioner running even when no one is in the room if the objective of having it running is to circulate air and maintain a stable room temperature. For example, in scorching weather, it can be helpful to leave a fan turned on to circulate cool air all through the house.
How to shut off a ceiling fan with no chain

With needle nose pliers, you may be able to remove any remaining chain that is even a small amount. Depending on whether the fan is linked directly to power (rather than being regulated by a wall switch), you may want to turn off the breaker to prevent the fan from running while you are working (to keep your sanity). The majority of fans click in the same manner. As a last resort, the fan can be replaced entirely if the chain is broken.
This can be done by taking the fan apart and replacing the switch if you enjoy tinkering and know a bit of this sort of thing. When you go to the hardware store to get a replacement switch, it’s generally a good idea to bring the old one with you as well. Please mark the wires after removing the broken switch; otherwise, you will have no idea where they have all gone.
If you keep flipping the switch, it will do nothing more than turn the fan on and off a few times. You could manage the fan speed by repeatedly turning the breaker on and off, but this would put a lot of strain on your arms and shoulders.
This is most likely a mechanical switch with a physical position at the high-speed position, rather than an electronic switch with a resettable state, which is a crucial point to note. As a result, cycling the power has no effect, and you must mechanically shift it to a different position to accomplish anything.
Given that you are working with electricity, you should avoid adjusting a faulty switch until you are familiar with the necessary safety precautions.
Frequently Asked Questions:
- How can one know whether a replacement switch is available in the market?
Inquire with your brand’s manufacturer or a home center store to see if a switch is available for purchase. You may have to remove other coverings to reach the control or the end of the chain. Disassembling the whole fan unit may make the entire repair process more accessible.
Conclusion
Again, make sure that the power has been turned off throughout the device when you do this.
If none of these measures prove successful, you may want to try purchasing a new fan, as suggested in other responses. They are not difficult to put in place. A nice feature is that many of them come with palm remote controls for controlling fan speed, light dimming, and other functions.